: 노트북 리눅스설치를 할려고 자료를 찾던중 아래 자료를 찾았는데
:
: 저의 딸리는 컴터실력과 영어실력으로는 해석이 50%도 불가능 합니다.
:
: 내용이 이해가 가시거나 해석이 가능 하신분은 리플좀 부탁드립니다
:
: __)
: Presario 1715 and Linux. January 26th 2002
:
: Hardware
:
: I have an ATI Radeon Mobility M6 LY (....:4c59) with an Intel 830M Agp bridge. I've included the entries at the end of
:  the page. I have also included some of the other important sections. Settings
: Following an install of Slackware 8.0, I compiled the latest kernel and patched it and recompiled it. Currently it's 2
: .4.17-pre8. I have also had to run the CVS Xfree 4.1.99 which is kinda funny, but works for the most part.
: Video
:
: This took me the longest to get working as the agpgart module didn't want to load at first. I found out that there are
:  two fixes to this. The second fix (don't use the first one!) is to choose Intel 440LX/BX/GX and I815/I830M/I840/I850 
: support in the Character Devices section of "make menuconfig" and *not* to select Intel I810/I815/I830 (on-board) supp
: ort. That should get the agpgart loaded nicely.
: **Note**
:
: I have been reading the changelogs recently. This problem has been fixed by Nicolas Aspert in 2.4.18-pre2. So if you a
: re using it or a later version, you shouldn't have the agpgart problem.
: Now, XF86 4.1.0 doesn't support the Radeon M6 LY so you will likely have to patch it, run a patched distro stock (eg. 
: Red Hat 7.2, Mandrake 8.0 I hear seem to work), or get the cvs version of XF outlined at www.xfree86.org/cvs. : Upon d
: oing that, in XF86Config, use device "radeon" in the driver section and add the line VideoRam 8192. Also, I think that
:  you won't be able to start up with the framebuffer modes. In lilo.conf, sometimes, you can specify vga=xxx for nice b
: ig screens in the console. I don't think this is possible anymore if you run the radeon. I haven't tested it and don't
:  feel like. Sound This one worked with the Intel 810 driver w/ the kernel.
:
:
: Ethernet
: Not yet.
:
:
: ACPI/ APM
: This is stupid. There isn't any APM. I'm sure there was a good rea$on for not using APM, but with the poorly supported
:  ACPI, you won't be able to check your batery status as of now.
: Wait for kernel updates.
:
: lscpi -v is below:
:
: 00:01.0 PCI bridge: Intel Corporation: Unknown device 3576 (rev 02) (prog-if 00 [Normal decode])
: 	Flags: bus master, 66Mhz, fast devsel, latency 96
: 	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
: 	I/O behind bridge: 00002000-00002fff
: 	Memory behind bridge: d0100000-d01fffff
: 	Prefetchable memory behind bridge: d8000000-dfffffff
:
: 00:1f.5 Multimedia audio controller: Intel Corporation: Unknown device 2485 (rev 01)
: 	Subsystem: Compaq Computer Corporation: Unknown device 005c
: 	Flags: bus master, medium devsel, latency 0, IRQ 5
: 	I/O ports at 1c00 [size=256]
: 	I/O ports at 1880 [size=64]
:
: 01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 4c59 (prog-if 00 [VGA])
: 	Subsystem: Compaq Computer Corporation: Unknown device b11b
: 	Flags: bus master, stepping, fast Back2Back, 66Mhz, medium devsel, latency 66, IRQ 11
: 	Memory at d8000000 (32-bit, prefetchable) [size=128M]
: 	I/O ports at 2000 [size=256]
: 	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
: 	Expansion ROM at <unassigned> [disabled] [size=128K]
: 	Capabilities:<available only to root>
:
: 02:04.0 Communication controller: CONEXANT: Unknown device 2f00 (rev 01)
: 	Subsystem: Compaq Computer Corporation: Unknown device 8d88
: 	Flags: medium devsel, IRQ 5
: 	Memory at d0210000 (32-bit, non-prefetchable) [disabled] [size=64K]
: 	I/O ports at 3040 [disabled] [size=8]
: 	Capabilities:<available only to root>
:
: 02:08.0 Ethernet controller: Intel Corporation: Unknown device 1031 (rev 41)
: 	Subsystem: Compaq Computer Corporation: Unknown device 0093
: 	Flags: medium devsel, IRQ 9
: 	Memory at d0200000 (32-bit, non-prefetchable) [size=4K]
: 	I/O ports at 3000 [size=64]
: 	Capabilities:<available only to root>