적수네 동네 - 질문과 답변 [ 게시물 수정 ]

	>> Edit article


			이름
			제목
			패스워드

USB 설정때문에 커널 컴파일 도 하였고, 그리고 부팅할 적에도 인식을 하는 것 
같은데, 마우스가 작동을 안 하는군요...
 www.linux-usb.org나 아니면 KLDP에 나와 있는 대로 하여도.
안 되는 것 같고...
어떻게 해야 하는지 모르겠습니다.
 커널 컴파일(kernel version 2.4.0) 할 때 
-->USB Human Interface Device (HID) support in the USB support(선택)
-->Input core support. 
       -->Mouse Support(선택)
-->Do not turn on USB HIDBP Mouse support. (선택하지 않음--선택하지 
    말라고 한것 같아서...선택해서 컴파일 해도 마찬가지 였음..)
 그리고 부팅해서
more /proc/interrupts
해서 보면 uhci-usb가 보이긴 하는데 계속 같은 값으로 있고요.
  more /proc/misc
해서 보면 마우스가 보이지 않습니다.
 cat /dev/input/mice
해서 usb mouse를 이리 저리 움직이니 무언가 모니터에 이상한 문자가 
뜨기는 했었은데, CTRL+C를 누르고 mouse를 움직이니 또 작동을 안 하더군요.
 어떻게 해야 하는지...
아시는 분, 가르켜 주시길..
참고적으로 영어를 해석해서 실행해 본다는게 너무 어려워서...
 내가 설정을 잘 못 했거나 아니면.....빠뜨린 것이 있는 것 같은데..
그럼..
 참고적으로 다음은 
  dmesg(부팅시의 로고)의 내용인데 참고하시고요...
  해결 방안을 말 해 주시면 감사 하겠습니다.
 ******************************************************************
******************************************************************
 Linux version 2.4.0 (root@Love_net) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #21 Wed Feb 21 13:24:44 KST 2001
BIOS-provided physical RAM map:
 BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
 BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
 BIOS-e820: 0000000000020000 @ 00000000000e0000 (reserved)
 BIOS-e820: 0000000003f00000 @ 0000000000100000 (usable)
 BIOS-e820: 0000000000001000 @ 00000000fec00000 (reserved)
 BIOS-e820: 0000000000001000 @ 00000000fee00000 (reserved)
 BIOS-e820: 0000000000020000 @ 00000000fffe0000 (reserved)
On node 0 totalpages: 16384
zone(0): 4096 pages.
zone(1): 12288 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux ro root=303
Initializing CPU#0
Detected 167.047 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 333.41 BogoMIPS
Memory: 62208k/65536k available (951k kernel code, 2940k reserved, 497k data, 184k init, 0k highmem)
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
CPU: Before vendor init, caps: 008001bf 00000000 00000000, vendor = 0
Intel Pentium with F0 0F bug - workaround enabled.
CPU: After vendor init, caps: 008001bf 00000000 00000000 00000000
CPU: After generic, caps: 008001bf 00000000 00000000 00000000
CPU: Common caps: 008001bf 00000000 00000000 00000000
CPU: Intel Pentium MMX stepping 03
Checking &#039;hlt&#039; instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfdb71, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Limiting direct PCI/PCI transfers.
Activating ISA DMA hang workarounds.
isapnp: Scanning for Pnp cards...
isapnp: Calling quirk for 01:00
isapnp: SB audio device quirk - increasing port range
isapnp: Card &#039;Creative ViBRA16X PnP&#039;
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd v1.8
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX3: IDE controller on PCI bus 00 dev 39
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: QUANTUM FIREBALL EX6.4A, ATA DISK drive
hdd: CRD-8160B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 12594960 sectors (6449 MB) w/418KiB Cache, CHS=784/255/63, (U)DMA
hdd: ATAPI 16X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
  http://www.scyld.com/network/ne2k-pci.html eth0: RealTek RTL-8029 found at 0x7f80, IRQ 9, 52:54:05:E0:F6:57.
PPP generic driver version 2.4.1
Registered PPPoX v0.5
Registered PPPoE v0.6.4
8139too Fast Ethernet driver 0.9.13 loaded
eth1: RealTek RTL8139 Fast Ethernet at 0xc4802f00, 00:e0:4c:b0:b2:05, IRQ 12
eth1:  Identified 8139 chip type &#039;RTL-8139C&#039;
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
sb: Creative ViBRA16X PnP detected
sb: ISAPnP reports &#039;Creative ViBRA16X PnP&#039; at i/o 0x220, irq 5, dma 1, 3
SB16: Bad or missing 16 bit DMA channel
sb: 1 Soundblaster PnP card(s) found.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB UHCI at I/O 0x7f40, IRQ 11
uhci.c: detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF c11e4280, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI-alt Root Hub
SerialNumber: 7f40
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c11e4280
usb.c: call_policy add, num 1 -- no FS yet
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: LAPB for Linux. Version 0.01 for NET4.0
devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 184k freed
uhci.c: root-hub INT complete: port1: 1a3 port2: 80 data: 2
hub.c: port 1 connection change
hub.c: port 1, portstatus 301, change 1, 1.5 Mb/s
hub.c: port 1, portstatus 303, change 0, 1.5 Mb/s
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: kmalloc IF c11e43c0, numif 1
usb.c: skipped 1 class/vendor specific interface descriptors
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Manufacturer: Cypress Sem.
Product: Cypress USB Mouse
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x5fe/0x3) is not claimed by any active driver.
  Length              = 18
  DescriptorType      = 01
  USB version         = 1.00
  Vendor:Product      = 05fe:0003
  MaxPacketSize0      = 8
  NumConfigurations   = 1
  Device version      = 4.9c
  Device Class:SubClass:Protocol = 00:00:00
    Per-interface classes
Configuration:
  bLength             =    9
  bDescriptorType     =   02
  wTotalLength        = 0022
  bNumInterfaces      =   01
  bConfigurationValue =   01
  iConfiguration      =   04
  bmAttributes        =   a0
  MaxPower            =  100mA
   Interface: 0
  Alternate Setting:  0
    bLength             =    9
    bDescriptorType     =   04
    bInterfaceNumber    =   00
    bAlternateSetting   =   00
    bNumEndpoints       =   01
    bInterface Class:SubClass:Protocol =   03:01:02
    iInterface          =   05
    Endpoint:
      bLength             =    7
      bDescriptorType     =   05
      bEndpointAddress    =   81 (in)
      bmAttributes        =   03 (Interrupt)
      wMaxPacketSize      = 0004
      bInterval           =   0a
usb.c: kusbd: /sbin/hotplug add 2
usb.c: kusbd policy returned 0xfffffffe
Adding Swap: 136544k swap-space (priority -1)--Hi...