적수네 동네 - 질문과 답변 [ 게시물 수정 ]

	>> Edit article


			이름
			제목
			패스워드

배드섹터입니다...
fsck 로 체크해 보세요... 
아예 배드섹터라고 등록시켜 버리면 그 다음부터는 저런 거 안납니다.
물론, 그 배드섹터가 옆으로 퍼지면서 .. 또 생기면 또 에러 납니다.
   : ##시스템이 부팅할때 뿌려대는 에러메세지내용## 
: 
: Sep 24 14:51:45 debian kernel: hda: 12672450 sectors (6488 MB) w/512KiB Cache, C 
: HS=788/255/63, (U)DMA 
: Sep 24 14:51:45 debian kernel: hdb: 19807200 sectors (10141 MB) w/466KiB Cache, 
: CHS=1232/255/63, UDMA(33) 
: Sep 24 14:51:45 debian kernel: Partition check: 
: Sep 24 14:51:45 debian kernel: hda:hda: dma_intr: status=0x51 { DriveReady Seek 
: Complete Error } 
: Sep 24 14:51:45 debian kernel: hda: dma_intr: error=0x84 { DriveStatusError BadC 
: RC } 
: Sep 24 14:51:45 debian kernel: hda: dma_intr: status=0x51 { DriveReady SeekCompl 
: ete Error } 
: Sep 24 14:51:45 debian kernel: hda: dma_intr: error=0x84 { DriveStatusError BadC 
: RC } 
: Sep 24 14:51:45 debian kernel: hda: dma_intr: status=0x51 { DriveReady SeekCompl 
: ete Error } 
: Sep 24 14:51:45 debian kernel: hda: dma_intr: error=0x84 { DriveStatusError BadC 
: RC } 
: Sep 24 14:51:45 debian kernel: hda: dma_intr: status=0x51 { DriveReady SeekCompl 
: ete Error } 
: Sep 24 14:51:45 debian kernel: hda: dma_intr: error=0x84 { DriveStatusError BadC 
: RC } 
: Sep 24 14:51:45 debian kernel: hdb: DMA disabled 
: Sep 24 14:51:45 debian kernel: ide0: reset: success 
: 
: ##하드드라이브 정보## 
: 
: /dev/hda: 
: 
: Model=FUJITSU MPD3064AT, FwRev=DD-03-47, SerialNo=05004274 
: Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } 
: RawCHS=13410/15/63, TrkSize=0, SectSize=0, ECCbytes=4 
: BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=16 
: CurCHS=13410/15/63, CurSects=12672450, LBA=yes, LBAsects=12672450 
: IORDY=yes, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} 
: PIO modes: pio0 pio1 pio2 pio3 pio4 
: DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 *udma3 udma4 
: AdvancedPM=yes: disabled (255) WriteCache=enabled 
: Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 
: 
: /dev/hdb: 
: 
: Model=IBM-DTTA-351010, FwRev=T56OA73A, SerialNo=WF0KFTZ3851 
: Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } 
: RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34 
: BuffType=DualPortCache, BuffSize=466kB, MaxMultSect=16, MultSect=16 
: CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=19807200 
: IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} 
: PIO modes: pio0 pio1 pio2 pio3 pio4 
: DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2 
: AdvancedPM=no WriteCache=enabled 
: Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4 
: 
: ##현재 하드드라이브설정상태## 
: 
: /dev/hda: 
: multcount = 16 (on) 
: I/O support = 1 (32-bit) 
: using_dma = 1 (on) 
: readahead = 128 (on) 
: 
: /dev/hdb: 
: multcount = 16 (on) 
: I/O support = 1 (32-bit) 
: using_dma = 1 (on) 
: readahead = 128 (on) 
: 
: ##마더보드 정보## 
: ----------VIA BusMastering IDE Configuration----------------
: Driver Version:                     3.34
: South Bridge:                       VIA vt82c686b
: Revision:                           ISA 0x40 IDE 0x6
: Highest DMA rate:                   UDMA100
: BM-DMA base:                        0xc000
: PCI clock:                          33.3MHz
: Master Read  Cycle IRDY:            0ws
: Master Write Cycle IRDY:            0ws
: BM IDE Status Register Read Retry:  yes
: Max DRDY Pulse Width:               No limit
: -----------------------Primary IDE-------Secondary IDE------
: Read DMA FIFO flush:          yes                 yes
: End Sector FIFO flush:         no                  no
: Prefetch Buffer:               no                  no
: Post Write Buffer:             no                  no
: Enabled:                      yes                 yes
: Simplex only:                  no                  no
: Cable Type:                   80w                 40w
: -------------------drive0----drive1----drive2----drive3-----
: Transfer Mode:       UDMA      UDMA       DMA       DMA
: Address Setup:       30ns      30ns      30ns      60ns
: Cmd Active:          90ns      90ns      90ns      90ns
: Cmd Recovery:        30ns      30ns      90ns      90ns
: Data Active:         90ns      90ns      90ns      90ns
: Data Recovery:       30ns      30ns      30ns      90ns
: Cycle Time:          50ns      60ns     120ns     180ns
: Transfer Rate:   39.9MB/s  33.3MB/s  16.6MB/s  11.1MB/s
: 
: ### 에러가 난 이유 ### 
: 위에 열거한 마더보드 사양이여서 커널컴파일 옵션중IDE chipset support/bugfixes 에서 
: CONFIG_BLK_DEV_VIA82CXXX=y 를켜고 
: sarge에서 xfs패치한 2.4.19 커널컴파일후 처음과 같은 에러가나자 
: # CONFIG_BLK_DEV_VIA82CXXX is not set 를 설정하지않고 
: CONFIG_BLK_DEV_PIIX=y 
: CONFIG_PIIX_TUNING=y 를 설정하고 컴파일 하니 에러 메세지 없어졌습니다. 
: 그래 그냥 그런가보다 하고 그냥 썼습니다. 
: 
: 그런데 haparm를 켠뒤로 다시 그러한 메세지가 나오자 이번에는 반대로 
: #CONFIG_BLK_DEV_PIIX is not set 
: #CONFIG_PIIX_TUNING is not set 를 끄고 
: CONFIG_BLK_DEV_VIA82CXXX=y 를 켜도 마찮가집니다. 
: 
: 
: # 현재 IDE chipset support/bugfixes 의 설정내용 
: 
: CONFIG_BLK_DEV_IDEPCI=y 
: CONFIG_IDEPCI_SHARE_IRQ=y 
: CONFIG_BLK_DEV_IDEDMA_PCI=y 
: CONFIG_IDEDMA_PCI_AUTO=y 
: CONFIG_BLK_DEV_IDEDMA=y 
: CONFIG_BLK_DEV_ADMA=y 
: #CONFIG_BLK_DEV_PIIX is not set 
: #CONFIG_PIIX_TUNING is not set 
: CONFIG_BLK_DEV_VIA82CXXX 
: CONFIG_IDEDMA_AUTO=y 
: CONFIG_BLK_DEV_IDE_MODES=y 
: 
: 
: 
: 어떻게 하면 저찜찜한 에러를 없앨수있을까요?--24시간 LSN delete daemon