적수네 동네 - 질문과 답변 [ 게시물 수정 ]

	>> Edit article


			이름
			제목
			패스워드

컴팩 플자 1715ap를 사용 하고 있습니다..
 래드햇7.2를 설치하려고 하는데 x윈도에서 그래픽카드를 지원하지 못하는군요
 이렇쿵 저러쿵 해서 아래의 문서를 찾았는데 딸리는 영어 실력으로는 ㅡ.ㅡ;
 해석이 불가해서 이렇게 부탁을 드립니다..
 무슨 커널업을 하라는것 같은데 답변좀 부탁드립니다..
 그리고 잴아래 acpi/apm은 무엇인가요? 
 Presario 1715 and Linux. January 26th 2002 
Hardware 
I have an ATI Radeon Mobility M6 LY (....:4c59) with an Intel 830M Agp bridge. I&#039;ve included the entries at the end of the page. I have also included some of the other important sections. 
Settings 
Following an install of Slackware 8.0, I compiled the latest kernel and patched it and recompiled it. Currently it&#039;s 2.4.17-pre8. I have also had to run the CVS Xfree 4.1.99 which is kinda funny, but works for the most part. 
Video 
This took me the longest to get working as the agpgart module didn&#039;t want to load at first. I found out that there are two fixes to this. The second fix (don&#039;t use the first one!) is to choose Intel 440LX/BX/GX and I815/I830M/I840/I850 support in the Character Devices section of "make menuconfig" and *not* to select Intel I810/I815/I830 (on-board) support. 
 That should get the agpgart loaded nicely.
 **Note** 
I have been reading the changelogs recently. This problem has been fixed by Nicolas Aspert in 2.4.18-pre2. So if you are using it or a later version, you shouldn&#039;t have the agpgart problem. 
 Now, XF86 4.1.0 doesn&#039;t support the Radeon M6 LY so you will likely have to patch it, run a patched distro stock (eg. Red Hat 7.2, Mandrake 8.0 I hear seem to work), or get the cvs version of XF outlined at www.xfree86.org/cvs.  Upon doing that, in XF86Config, use device "radeon" in the driver section and add the line VideoRam 8192. Also, I think that you won&#039;t be able to start up with the framebuffer modes. In lilo.conf, sometimes, you can specify vga=xxx for nice big screens in the console. I don&#039;t think this is possible anymore if you run the radeon. I haven&#039;t tested it and don&#039;t feel like.
  Sound 
This one worked with the Intel 810 driver w/ the kernel.
  Ethernet 
Not yet.
  ACPI/ APM 
This is stupid. There isn&#039;t any APM. I&#039;m sure there was a good rea$on for not using APM, but with the poorly supported ACPI, you won&#039;t be able to check your batery status as of now.
 Wait for kernel updates. 
 lscpi -v is below: 
 00:01.0 PCI bridge: Intel Corporation: Unknown device 3576 (rev 02) (prog-if 00 [Normal decode])
	Flags: bus master, 66Mhz, fast devsel, latency 96
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: d0100000-d01fffff
	Prefetchable memory behind bridge: d8000000-dfffffff
 00:1f.5 Multimedia audio controller: Intel Corporation: Unknown device 2485 (rev 01)
	Subsystem: Compaq Computer Corporation: Unknown device 005c
	Flags: bus master, medium devsel, latency 0, IRQ 5
	I/O ports at 1c00 [size=256]
	I/O ports at 1880 [size=64]
 01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 4c59 (prog-if 00 [VGA])
	Subsystem: Compaq Computer Corporation: Unknown device b11b
	Flags: bus master, stepping, fast Back2Back, 66Mhz, medium devsel, latency 66, IRQ 11
	Memory at d8000000 (32-bit, prefetchable) [size=128M]
	I/O ports at 2000 [size=256]
	Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: <available only to root>
 02:04.0 Communication controller: CONEXANT: Unknown device 2f00 (rev 01)
	Subsystem: Compaq Computer Corporation: Unknown device 8d88
	Flags: medium devsel, IRQ 5
	Memory at d0210000 (32-bit, non-prefetchable) [disabled] [size=64K]
	I/O ports at 3040 [disabled] [size=8]
	Capabilities: <available only to root>
 02:08.0 Ethernet controller: Intel Corporation: Unknown device 1031 (rev 41)
	Subsystem: Compaq Computer Corporation: Unknown device 0093
	Flags: medium devsel, IRQ 9
	Memory at d0200000 (32-bit, non-prefetchable) [size=4K]
	I/O ports at 3000 [size=64]
	Capabilities: <available only to root>