안녕하세요
 초보 시스템 엔지니어 입니다.
 다름 아니라....
 저는 보드 ( gigabyte ) 에 LSI 53C1010-66 이 온보드 되어 있는데요....
 여기다가 solaris 8 x86 을 깔려고 합니다.
 그래서 LSI 홈페이지에 가서 드라이버를 다운 받은 다음에 도스 상태에서
 rawrite 를 시켰습니다. 그런 다음 아래와 같은 방법으로 인스톨을 했죠....
(설치한 방법은 아래의 드라이버 매뉴얼 페이지에서 복사한 것입니다. )
 그런데 ... 분명 드라이버 파일을 카피 했는데....
 하드웨어 스캔단계에서 잡히질 않습니다.
 그러니 당연히 네트워크 설정 다음에 install 시에
 "디스크를 찾을 수 없습니다. " 라는 메시지가 나옵니다.
 도데체 뭐가 잘못된 건지 모르겠습니다.
 비슷한 경험이나...
 경험많으신 분들의 조언을 듣고 싶습니다. 
 끝까지 읽어 주셔서 감사합니다.
  *  *  *  *  *  *  *  New System Installation for Solaris *  *  *  *  *  *  * 
 To use the driver on the SYMHISL Driver Update diskette to install Solaris
(Intel Platform Edition) on a machine, follow the steps below. Use the
appropriate Solaris Device Configuration Assistant Diskette appropriate for
your release of Solaris 8 as the boot diskette.
 1.  Insert the Solaris Device Configuration Assistant Diskette into your
    machine's diskette drive. Also insert the Solaris Installation CD-ROM;
    or for network installation, verify with your system administrator that
    the Solaris Network Installation image is available on your network.
 2.  Turn on your Machine.
 3.  When the Solaris Device Configuration Assistant screen appears, choose
    F4_Add Driver.
     The message Enumerating buses ... appears. Then, the Install Driver Update
    screen appears.
 4.  Remove the Solaris Device Configuration Assistant Diskette from the
    diskette drive and insert the first Solaris Driver ITU diskette you want.
 5.  Press F2_Continue.
     The Select Solaris System Version screen appears.
 6.  Select the appropriate Solaris operating system, and press F2_Continue.
     The Loading Driver Update Software screen appears, along with a progress
    bar that shows the percentage of drivers that have been extracted from the
    diskette. Drivers are read into memory and survive long enough for the
    system to successfully boot to its installation program. When all the new
    drivers on the diskette have been processed, the Continue Driver Update
    Installation screen appears.
 7.  Remove the Solaris Driver ITU diskette from the diskette drive and insert
    the next Solaris Driver ITU diskette you want, if any.
 8.  Press F2_Continue.
     The Loading Driver Update Software screen appears, along with a progress
    bar that shows the percentage of drivers that have been extracted from the
    diskette. Drivers are read into memory and survive long enough for the
    system to successfully boot to its installation program. When all the new
    drivers on the diskette have been processed, the Continue Driver Update
    Installation screen appears.
 9.  Repeat Step 4 through Step 8 until all the Solaris Driver ITU
    diskettes you want are installed.
 10. When all the drivers are processed, remove the Solaris Driver ITU diskette
    from the diskette drive and reinsert the Solaris Device Configuration
    Assistant Diskette.
     IMPORTANT: Do not remove the Solaris Device Configuration Assistant
               Diskette from the diskette drive until you see the following
               message displayed in a dialog box:
                "If you want to bypass the device configuration and
               boot screens when the system reboots, eject the
               Device Configuration Assistant/Boot diskette now."
 11. Press F2_Continue.
     The Solaris Device Configuration Assistant screen appears.
 12. Press F2_Continue.
     The "Enumerating buses" message appears.
     The Scanning Devices screen appears. System devices are scanned. When
    scanning is complete, the Identified Devices screen appears.
 13. Press F2_Continue.
     The message "Loading driver ..." appears followed by messages about the
    drivers that are required to boot your system. After a few seconds, the
    Boot Solaris screen appears.
 14. At the Boot Solaris screen, select the device controller attached to the
    device that contains your install medium.
 15. Press F2_Continue.
     Drivers for the device controller that you selected are displayed. Your
    system boots to run the install program. The install program starts and
    your machine begins booting the complete Solaris operating environment.
    The following messages appear some time later, and prompts you to
    insert each of the Solaris Driver ITU diskette(s) required to install
    into your machine:
        Installing unbundled device driver support
       Extracting driver list from tree..
       <ITU diskette name> driver-name...
        Please insert the Driver Update diskette labeled <ITU diskette name>
       Press <ENTER> when ready.
 16. Remove the Solaris Device Configuration Assistant Diskette. Reinsert
    the SYMHISL Driver ITU diskette that you inserted earlier into the
    diskette drive.
 17. Press Enter.
     Packages and/or patches that contain the new drivers are installed from
    the diskette onto your machine. Messages about each installation appear
    accordingly.
     o When the following prompt appears:
       Please insert the Driver Update diskette labeled <SYMHISL>
      Press <ENTER> when ready.
     
      Insert the SYMHISL ITU diskette into the floppy drive.
      When the prompt asking if you wish to create a new instance of the
      SYMHISL package appears, respond with 'n' for NO.  When the prompt
      asking if you wish to overwrite the existing instance of SYMHISL
      appears, respond with 'y' for YES.
 18. If drivers on other Solaris Driver ITU diskettes are required, remove
    the Driver ITU diskette from the diskette drive, insert the next Driver
    ITU diskette when prompted to insert it, and press Enter. Repeat this
    process until all drivers you need are installed.
 19. Press Enter.
     When installation has completed, the message "Installation complete" 
    appears.
 20. Remove the diskette from the diskette drive.
 21. Reboot your machine.
     When the Solaris operating environment is finished booting and running, the
    new devices whose drivers that you installed are available for use.