xconfigurator로 잡의면 card database missing라고나오면서 튕기고..
 xf86config로 잡을려면 그래픽카드리스트에 부두밴쉬(tdfx)가 아예없어서 우선 아무그래픽
 카드를 선택해서  /etc/X11/XF86Config를 생성해서 수동으로 부두밴쉬에 맞게 아래와 같이
 했습니다. 그런데.. 이게 어찌된건지 해상도가 640x480으로만 뜹니다.
 같은 부두밴쉬 쓰시는분 조언부탁 바랍니다. 그리고 XF86config파일을 멜로좀 보내주세여..
 비교줌 해볼려구여~~ 왕부탁드립니다.
 -----------------------------------------------------------------------------
# **********************************************************************
# Monitor section
# **********************************************************************
 # Any number of monitor sections may be present
 Section "Monitor"
     Identifier  "My Monitor"
 # HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
     HorizSync   31.5
 #    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies
 # VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
     VertRefresh 50-70
 EndSection
  # **********************************************************************
# Graphics device section
# **********************************************************************
 # Any number of graphics device sections may be present
 # Standard VGA Device:
 Section "Device"
    Identifier	"Voodoo"
    VendorName	"3dfx"
    BoardName	"tdfx"
 # The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.
 #    Chipset	"generic"
 # The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
     Driver     "tdfx"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.
 #    BusID      "PCI:0:10:0"
 #    VideoRam	256
 #    Clocks	25.2 28.3
 EndSection
 # Device configured by xf86config:
 Section "Device"
    Identifier  "y"
    Driver      "tdfx"
    VideoRam    16204
 # Device section for Cirrus Logic GD5430/34-based cards.
    #MemBase 0x00e00000		# ISA card that maps to 14Mb
    #MemBase 0x04000000		# VLB card that maps to 64Mb
    #MemBase 0x80000000		# VLB card that maps to 2048Mb
    #MemBase 0x02000000		# VLB card that maps to 32Mb
    #Option "linear"
# Use Option "no_bitblt" if you have graphics problems. If that fails
# try Option "noaccel".
# Refer to /usr/X11R6/lib/doc/README.cirrus.
# To allow linear addressing, uncomment the Option line and the
# address that the card maps the framebuffer to.
    # Insert Clocks lines here if appropriate
EndSection
  # **********************************************************************
# Screen sections
# **********************************************************************
 # Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "Voodoo"
    Monitor     "My Monitor"
    DefaultDepth 16
    Subsection "Display"
        Depth       16
        Modes       "1152x864"
        ViewPort    0 0
    EndSubsection
EndSection