USB포트에 연결하는 플레쉬메모리타입의 보조 기억장치는 인식을
시켰는데요..
USB포트에 연결하는 하드디스크는 리눅스에서 인식을 못시키겠네요..
어떻게 해야하는지 가르쳐주세요..
 ==========================================================
#dmesg
....
...(생략)
..
.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision:1.251 $ time 01:59:29 Jun 24 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:07.2
PCI: The same IRQ used for device 00:07.3
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:07.3
PCI: The same IRQ used for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport_pc: Via 686A parallel port: io=0x378, irq=7
ip_conntrack (1023 buckets, 8184 max)
spurious 8259A interrupt: IRQ7.
Via 686a audio driver 1.1.14b
PCI: Found IRQ 10 for device 00:07.5
ac97_codec: AC97 Audio codec, id: 0x4943:0x4511 (ICE1232)
via82cxxx: board #1 at 0xDC00, IRQ 10
via_audio: ignoring drain playback error -11
hub.c: USB new device connect on bus1/2, assigned device number 3
usb.c: USB device 3 (vend/prod 0x5e3/0x702) is not claimed by any active driver.
SCSI subsystem driver Revision:1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
usb-uhci.c: interrupt, status 2, frame# 1569
usb-uhci.c: interrupt, status 3, frame# 1570
scsi0 : SCSI emulation for USB Mass Storage devices
usb-uhci.c: interrupt, status 2, frame# 1574
usb-uhci.c: interrupt, status 3, frame# 1576
usb-uhci.c: interrupt, status 2, frame# 1578
usb-uhci.c: interrupt, status 3, frame# 1580
usb-uhci.c: interrupt, status 2, frame# 1582
usb-uhci.c: interrupt, status 3, frame# 1584
usb-uhci.c: interrupt, status 2, frame# 1586
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
USB Mass Storage support registered.
#
#
=====================================================
 이걸보면 USB장치가 발견이 되는것 같은데..
USB장치는 SCSI장치로 인식되어..
#cat /proc/scsi/scsi라고 해보면
Attached deices: none
라고 나오네요...
어떻게 방법이 없을까요?